Audi Resource

Connectors, door control unit, driver side -J386

32-pin connector (to door trim)

A1 - Vacant

A2 - LED button for interior monitoring (deactivate interior monitoring)

A3 - Button for interior monitoring

A4- Alarm system Off button (tilt sensor inactive)

A5 - Tank cap release button

A6 - Mirror adjustment - right/left

A7 - Mirror adjustment - X/Y

A8 - Window lifter button rear left

A9 - Window lifter button rear right

A10 - Window lifter button front right

A11 - Supply seat memory terminal 30 (only with seat memory fitted)

A12 - LED button for alarm system off (deactivate tilt sensor)

A13 - Child lock switch, right/left

A14 - Vacant

A15 - LED - Child lock button, right

A16 - LED - Child lock button, left

A17 - Boot lid/tailgate remote control switch

A18 - LED - Interior locking button

A19 - Ambient lighting

A20 - Door warning/entry light

A21 - Switch (terminal 31)

A22 - Terminal 58s

A23 - Interior locking button (LOCK/UNLOCK)

A24 - Interior door handle switch

A25 - Window lifter button front left (local)

A26 - Seat memory - position button 3 - 4 (only with seat memory fitted)

A27 - Seat memory - position button 1 -2 (only with seat memory fitted)

A28 - Seat memory - store button (only with seat memory fitted)

A29 - Seat memory - ON/OFF (only with seat memory fitted)

A30 - Seat memory - terminal 30 (only with seat memory fitted)

A31 - Seat memory - Emergency-off (only with seat memory fitted)

A32 - Vacant

16-pin connector (exterior mirrors)

B1 - Mirror adjustment motor Y-direction

B2 - Mirror adjustment motor X-direction

B3 - Mirror adjustment motor X/Y-direction

B4- Vacant

B5 - Mirror heating

B6 - Mirror heating (terminal 31)

B7- Vacant

B8 - Mirror exterior light

B9 - Mirror folding motor +

B10 - Mirror folding motor -

B11 - Mirror dip signal 1 (EC mirror +)

B12 - Mirror dip signal 2 (EC mirror -)

B13 - Mirror supply, potentiometer (only with seat memory fitted)

B14 - Mirror status position X (only with seat memory fitted)

B15 - Mirror status position Y (only with seat memory fitted)

B16 - Mirror potentiometer (terminal 31; only with seat memory fitted)

20-pin connector

C1 - Exterior door handle illumination

C2 - Feedback locked/safe

C3 - Door contact switch

C4 - Motors (terminal 31)

C5 - Central locking motor (Safe)

C6 - Central locking motor

C7- Vacant

C8 - Keyswitch close/open

C9 - Switch (terminal 31)

C10 - Exterior door handle switch

C11 - Latch (pre-latch; for power latch)

C12 - CL button in exterior door handle, driver side

D1 - Terminal 31

D2 - Terminal 30 (central locking)

D3 - Enable terminal 30

D4 - CAN - High

D5 - CAN-Low

D6 - Terminal 30 (window lifters)

D7 - Communication wire to power latch

D8 - Seat memory - emergency-off

Reading measured value block (door control unit, driver side -J386)

The following measured values are displayed:

Measured value block 001:

Readout 01:

xxxxxxxx (0=not active/1=active)

1: Catch (pre-latch switch in closure unit)

(only fitted with power latch [PR number:GZ2])

2: Door contact switch

3: Feedback lock locked

4: Feedback lock safed (in USA not relevant)

5: CL inside switch unlock

6: CL inside switch lock

7: Key switch close

8: Key switch open

Readout 02:

xxxxxxxx (0=not active/1=active)

1: Alarm system off button

2: Interior monitor button (not fitted in USA)

3: Child lock button, right

4: Child lock button, left

5: Tank cap release switch

6: Tailgate remote release button

7: Driver door handle switch

8: Central locking button in exterior door handle, driver side

Readout 03:

xxxx (0=not active/1=active)

1: One-wire fault in Group convenience system data bus

2: Terminal 15

3: Terminal 30, central locking

4: Terminal 30, window lifters

Readout 04:

Vehicle voltage

(voltage in V)

Measured value block 002:

Readout 01:

Local window lifter button

(auto. open/auto. close/manual open/manual close/unpressed/implausible)

Readout 02:

Window lifter button DS for front PS

(auto. open/auto. close/manual open/manual close/unpressed/implausible)

Readout 03:

Window lifter button DS for front RL

(auto. open/auto. close/manual open/manual close/unpressed/implausible/n.fitted)

Readout 04:

Window lifter button DS for front RR

(auto. open/auto. close/manual open/manual close/unpressed/implausible/n.fitted)

Measured value block 003:

Readout 01:

Window lifter position

(0 ... 100%/no readout)

KNotes:

J With readout: No readout A Window not standardised

J 0% corresponds to open; 100% corresponds to closed

Readout 02:

Calculated temperature of window lifter motor

(-50...200°C/no readout/no comm.)

Readout 03:

xxxxxxx (0=not active/1=active)

1: Insulating glass

2: Window lifters standardised

3: Window lifters thermal protection

4: Enable window lifters issued

5: Roll-back function activated

6: Recirculated air enable

7: Correction value

KNote:

- Correction value A in case of mech. slow movement of window lifter motor or this bit is set shortly before activation of roll-back.

Readout 04:

Window lifter movement

open/close/stopped)

Measured value block 004:

Readout 01:

Mirror adjustment switch

(pos. X+/pos. X-/pos. Y+/pos. Y-/unpressed/implausible)

Readout 02:

Mirror selection switch

(left/right/unpressed/fold in/implausible)

Readout 03:

Memory buttons (optional)

xxxxxx (0=not active/1=active/implausible/not present)

1: Position button 1

2: Position button 2

3: Position button 3

4: Position button 4

5: Memory emergency off

6: Memory button

Readout 04:

Vacant

Measured value block 005:

Readout 01:

Road speed signal

(0..00.255km/h/no comm./no readout)

Readout 02:

Ambient temperature

(-50...200°C/no comm./no readout)

Readout 03:

Calculated output of mirror heating

(0 ... 100%/no readout)

Readout 04:

Mirror heating

(heating ON/heating OFF)